1.Fitting the INFINITI G35 RWD; Coupe2003-2009 NISSAN 350Z RWD2.Package Includes: 14x Front Control Arm Ball Joints Suspension Kit Fits 2003-2007 INFINITI G35 RWD
1.Fitting the Followingvehicle:
2003-2007 INFINITI G35 RWD; Coupe2003-2009 NISSAN 350Z RWD
2.Package Includes:
2x Front Inner Tie Rod End -EV802791x Front Sway Bar End Link - Passenger Side -K7501001x Front Sway Bar End Link - Driver Side -K7501011x Front Outer Tie Rod End - Passenger Side -ES805781x Front Outer Tie Rod End - Driver Side -ES805792x Rack and Pinion Bellow -1x Front Lower Control Arm and Ball Joint Assembly - Rear Position Passenger Side -K6213721x Front Lower Control Arm and Ball Joint Assembly - Rear Position Driver Side -K6213731x Front Upper Control Arm and Ball Joint - Driver Side -K6216901x Front Upper Control Arm and Ball Joint - Passenger Side -K6219361x Front Lower Control Arm - Forward Position - Passenger Side -K641594,CMS301641x Front Lower Control Arm - Forward Position - Driver Side some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts.
Please check above compatibility list to make sure it fits your vehicle.
Tie-Rod End Replacement Guideline:
If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely.
This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod.
Picture(A)
Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance.
1.Lift the vehicle and dismount the front axle wheels.
2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes.
Picture(B)
3.Dismount the front underride />4.Loosen the fastening nut from the tie rod and remove it completely.
5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Picture(D)
6.Remove the clamp of the bellow on the steering gear.
7.Push the bellow towards the tie rod end.
Picture(E)
8.Unscrew the inner tie rod from the rack.
9.Clean the sealing face of the bellow at the steering gear.
Picture(F)
10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair.
11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle />12.Mount the bellow and close the clamps with the appropriate special tool.
Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Picture(H)
13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer.
Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(I)
14.Mount the front underride guard.
15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer.
16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
17.Perform a test drive.
Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission.
Sway Bar Stabilizer Link Replacement Guideline:
While driving, the following signs may indicate a faulty sway barstabilizer link:
(1).Rattling and thumping noises on rough roads.
(2).Imprecise vehicle handling.
(3).Stronger inclination of the vehicle during cornering.
If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Picture(A)
1.Raise vehicle and remove front wheels.
Tip:Always check both stabilizer links and replace them in pairs if necessary.
2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
4.Press stabilizer link out of torsion the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Tip:If the ball stud also starts to turn, hold it with a suitable stabilizer link at suspension strut out of new stabilizer link at suspension stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable new stabilizer link at stabilizer.
10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
12.Conclude with a test drive.
Frequently Asked Questions
(1).Do I need to replace the control arm if the bushings are worn?
Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm.
(2).What happens if a ball joint breaks?
When a ball joint breaks, you will hear a mysterious noise inside your car wheel.
Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control.
If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious.
Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car.
(3).What happens if I don't replace ball joints?
If you don't want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new.
(4).Do Ineed to grease new ball joints?
I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card.
(5).Why should I get my tie rods inspected on a regular basis?
If you don't get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it's possible that bad tie rods may be the culprit. Your vehicle's tires will also show uneven wear on the inside and outside edge of the tire when there's a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning /> One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive.
(7).Shaking
As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom.
(8).Wandering
If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may "wander" as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic.
(9).What are the symptoms of a bad sway bar?
Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns.
(10).What happens when a sway bar breaks?
Because a sway bar helps the car's suspension to put more pressure on loaded springs, a broken sway bar means that the car's suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds.
Item SpecificsPlacement on Vehicle FrontType Tie Rod EndBrand CARMASUSPENSIONSUniversal Fitment NoManufacturer Part Number CA84204501NSManufacturer Warranty 10 YearInterchange Part Number Part Number K621690,K621936,K641594,CMS30164,car tie rod replacementSuperseded Part Number K641595,CMS30163,stabilizer anti sway bar linkage,anti roll barFeatures GreasablePerformance Part NoItems Included Mounting HardwareCotter Pin Hole YesMaterial Alloy SteelMounting Style Bolt-OnFinish Coated
Discount Targeted Disounts Terms(1).Targeted Discount Terms only apply to auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link.(2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items.(3).Targeted Discount will be refunded from buyer's payment, which means CARMASUSPENSIONS won't provide any extra targeted discounts if full refund is issued.Targeted Shipping Discount(4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items.Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes.(5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received.(6).CARMASUSPENSIONS has the final power of interpretation of all the above Targeted Discount Terms and Procedures.Shipping WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.govProposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.(1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available.(2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable.(3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available.(4).Global Shipping Program is temporarily not available due to the reason for package dimensions.(5).We usually need a 1-2business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6business days after your payment is received.(6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received.(7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more.Warranty Items valued over $15 on that include a warranty or service contract must contain additional details in seller's listing description.10 Year Warranty Terms and Procedures(1).The warranty terms only apply to the auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link.(2).CARMASUSPENSIONS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements.(3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period.(4).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests.(5).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests.(6).CARMASUSPENSIONS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly.(7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately.(8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original order details if required, including buyer user name, shipping address, item title, item id, final sales price.(9).CARMASUSPENSIONS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures.Return (1).Most of items support 60 Days Money Back Guarantee.(2).Refunds will be credited within 2 or 3 business days after returned item(s) is received.
Best Sales For Ford Ranger & Explorer 4WD 10Pcs Front Control Arms Ball Joints Tie Rods Kit USD 81.69 For 2003-2008 Toyota Corolla 12x Lower Control Arm Ball Joint Tie Rod End Kit USD 85.49 For Chevrolet Malibu Pontiac G6 Saturn Aura 8 x Control Arm Sway Bar Tie Rod Kit USD 101.26 10pc Fits FORD F-150 2005 - 2008 Suspension Front Upper Lower Control Arms Part USD 248.89 Fits Ford F-250 F-350 Super Duty - 4WD 4x4 New 5x Complete Front Suspension Kit USD 108.29 Newly Listed Catalytic Converter Manifold For 2007-2013 Nissan Altima L4 2.5L 674-933 EPA USD 114.00 2pc Front Upper Driver Control Arm and Lower Ball Joint Fit For 97-99 Acura CL USD 39.51 10x Front Upper & Lower Control Arms Ball Joints Fit for 92-94 1995 Honda Civic USD 74.66 Catalytic Converter Manifold For Mitsubishi Eclipse 2.4L 2006 2007 2008 09-2012 USD 114.00 Set Of 4 Front Suspension Kit Sway Bar Tie Rod End Fits 03-08 Mini Cooper Brand USD 32.67 14x Front Control Arm Ball Joints Suspension Kit Fits 2003-2007 INFINITI G35 RWD
1.Fitting the Followingvehicle:
2003-2007 INFINITI G35 RWD; Coupe2003-2009 NISSAN 350Z RWD
2.Package Includes:
2x Front Inner Tie Rod End -EV802791x Front Sway Bar End Link - Passenger Side -K7501001x Front Sway Bar End Link - Driver Side -K7501011x Front Outer Tie Rod End - Passenger Side -ES805781x Front Outer Tie Rod End - Driver Side -ES805792x Rack and Pinion Bellow -1x Front Lower Control Arm and Ball Joint Assembly - Rear Position Passenger Side -K6213721x Front Lower Control Arm and Ball Joint Assembly - Rear Position Driver Side -K6213731x Front Upper Control Arm and Ball Joint - Driver Side -K6216901x Front Upper Control Arm and Ball Joint - Passenger Side -K6219361x Front Lower Control Arm - Forward Position - Passenger Side -K641594,CMS301641x Front Lower Control Arm - Forward Position - Driver Side some parts have grease fittings, other parts are factory sealed, but do not affect the fit and quality of the parts.
Please check above compatibility list to make sure it fits your vehicle.
Tie-Rod End Replacement Guideline:
If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely.
This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod.
Picture(A)
Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance.
1.Lift the vehicle and dismount the front axle wheels.
2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes.
Picture(B)
3.Dismount the front underride />4.Loosen the fastening nut from the tie rod and remove it completely.
5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator.
Picture(D)
6.Remove the clamp of the bellow on the steering gear.
7.Push the bellow towards the tie rod end.
Picture(E)
8.Unscrew the inner tie rod from the rack.
9.Clean the sealing face of the bellow at the steering gear.
Picture(F)
10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle.
Note:Always use new self-locking nuts and bolts for a reliable repair.
11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle />12.Mount the bellow and close the clamps with the appropriate special tool.
Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance.
Picture(H)
13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer.
Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure.
Tip:Secure the ball stud against twisting with a suitable tool.
Picture(I)
14.Mount the front underride guard.
15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer.
16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications.
17.Perform a test drive.
Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission.
Sway Bar Stabilizer Link Replacement Guideline:
While driving, the following signs may indicate a faulty sway barstabilizer link:
(1).Rattling and thumping noises on rough roads.
(2).Imprecise vehicle handling.
(3).Stronger inclination of the vehicle during cornering.
If the sway bar stabilizer link is found to be defective, it should be replaced as described below.
Picture(A)
1.Raise vehicle and remove front wheels.
Tip:Always check both stabilizer links and replace them in pairs if necessary.
2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few the lower fastening nut of the stabilizer link at the stabilizer and remove.
Tip:If the ball stud also starts to turn, hold it with a suitable tool.
4.Press stabilizer link out of torsion the upper fastening nut of the stabilizer link at the suspension strut and remove it.
Tip:If the ball stud also starts to turn, hold it with a suitable stabilizer link at suspension strut out of new stabilizer link at suspension stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable new stabilizer link at stabilizer.
10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer.
Tip:Secure the ball stud against twisting with a suitable the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer.
Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension.
12.Conclude with a test drive.
Frequently Asked Questions
(1).Do I need to replace the control arm if the bushings are worn?
Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm.
(2).What happens if a ball joint breaks?
When a ball joint breaks, you will hear a mysterious noise inside your car wheel.
Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control.
If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious.
Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car.
(3).What happens if I don't replace ball joints?
If you don't want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new.
(4).Do Ineed to grease new ball joints?
I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card.
(5).Why should I get my tie rods inspected on a regular basis?
If you don't get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it's possible that bad tie rods may be the culprit. Your vehicle's tires will also show uneven wear on the inside and outside edge of the tire when there's a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning /> One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive.
(7).Shaking
As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom.
(8).Wandering
If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may "wander" as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic.
(9).What are the symptoms of a bad sway bar?
Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns.
(10).What happens when a sway bar breaks?
Because a sway bar helps the car's suspension to put more pressure on loaded springs, a broken sway bar means that the car's suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds.
DiscountShippingWarrantyReturnresponse Targeted Disounts Terms(1).Targeted Discount Terms only apply to auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link.(2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items.(3).Targeted Discount will be refunded from buyer's payment, which means CARMASUSPENSIONS won't provide any extra targeted discounts if full refund is issued.Targeted Shipping Discount(4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items.Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes.(5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received.(6).CARMASUSPENSIONS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.govProposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.(1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available.(2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable.(3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available.(4).Global Shipping Program is temporarily not available due to the reason for package dimensions.(5).We usually need a 1-2business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6business days after your payment is received.(6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received.(7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on that include a warranty or service contract must contain additional details in seller's listing description.10 Year Warranty Terms and Procedures(1).The warranty terms only apply to the auto parts purchased from CARMASUSPENSIONS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link.(2).CARMASUSPENSIONS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements.(3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period.(4).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests.(5).CARMASUSPENSIONS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise CARMASUSPENSIONS has the right to refuse any replacement requests.(6).CARMASUSPENSIONS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly.(7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately.(8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original order details if required, including buyer user name, shipping address, item title, item id, final sales price.(9).CARMASUSPENSIONS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee.(2).Refunds will be credited within 2 or 3 business days after returned item(s) is received.
Copyright of carmasuspensions. All rights reserved.
